Hitachi C10FSH 10-Inch Sliding Compound Miter Saw with Laser Review
When you work with building materials, it's important to have a miter saw that delivers powerful, accurate cutting. The Hitachi C10FSH 10-Inch Sliding Compound Miter Saw with Laser is just such a tool
Visit WebsiteHitachi C10FSH 10-Inch Sliding Compound Miter Saw with Laser Review
When you work with building materials, it’s important to have a miter saw that delivers powerful, accurate cutting. The Hitachi C10FSH 10-Inch Sliding Compound Miter Saw with Laser
Consistent Cutting Power
As you probably know, there are plenty of miter saws that deliver a lot of cutting power. The trouble with these saws has always been a lack of consistency. To get the best cuts you need a saw that reaches top cutting speeds and stays at those blade speeds while you cut through lumber. The Hitachi C10FSH 10-Inch Sliding Compound Miter Saw with Laser
Covers all the Angles
When you’re cutting a lot of lumber, there’s a good chance that you’ll be cutting at the same angles again and again. A lot of miter saws require you to manually dial in to the angles that you need. And while you can do that with the Hitachi C10FSH 10-Inch Sliding Compound Miter Saw, it’s also built with 10 positive stops to allow you to quickly set the saw up at the most common angles used. And those stops are identical to the right and left, so you’ll never have to worry about frustrating, manual set ups to get the saw to cut at the most commonly used angles.
Cutting easily-deformed materials, such as aluminum sash
Materials such as aluminum sash can easily deform when tightened too much in a vise assembly. Thiswill cause inefficient cutting and possible overload of the motor.
When cutting such materials, use a wood plate to protect the workpiece. Set the wood plate near the cutting section. When cutting aluminum materials, coat the saw blade with cutting oil (non-combustible) to achieve smooth cutting and a fine finish.
In addition, in case of a U-shaped workpiece, use the wood plate to ensure
stability in the lateral direction, and clamp it near the cutting section of the workpiece and tighten it using both the vise assembly and the clamp available in the market.
Do you cut a lot of crown moldings, if so then this saw has the additional option that you can buy crown molding cutting accessories. The Crown molding Stopper (L) and (R) (optional accessories) allows for
easier cuts of crown molding without tilting the saw blade this is a great bit of kit if your cutting a lot of crowns
.Then there is the crown molding vise which can be mounted on either the left fence or the right fence It can unite with the slope of the crown molding and vice can be pressed down. simply align the upper surface of the fence to either of the three v-grooves on the vise shaft surface or to the lower surface of the screw holder.
Therefore, the vise assembly can be attached in either of three positions to ensure proper height adjustment making the cutting of crown molds so much easier and safer for you.
Laser Marker Technology for Perfect Cuts Everytime
Hitachi equipped the C10FSH with its exclusive Laser Marker System, which can be activated before the blade is in motion for exact alignment and predictable blade placement. The laser marker is easily adjustable to suit your preferences, simply line up the laser with your mark on the workpiece, and the saw blade will make an exact cut along the laser guide. As long as your measurements are right, your cuts will be, too!
Hitachi C10FSH 10-Inch Sliding Compound Miter Saw with Laser
- Powerful 12 amp motor reaches top blade speeds of 3,800 rpm
- The electronic speed control allows consistent cutting speeds on every cut
- 10 positive stops for quick angled cuts
- The fence pivots to support every piece that you cut
- Carbide blade and stainless steel detent plate
- Comes with the saw, TCT saw blade, dust bag and 10 mm box wrench
- Dimensions: 20-3/4 by 41-1/2 by 24-1/4 inches
- Weighs in at just 43 pounds
- Backed by a 5-year warranty
- Laser marker for perfect alignment on every cut
Always replace the saw blade immediately upon the first sign of deterioration or damage. A damaged saw blade can cause personal injury and a worn saw blade can cause ineffective operation and possible overload to the motor.
What People are Saying About the Hitachi C10FSH 10-Inch Sliding Compound Miter Saw with Laser
While doing research for this Hitachi C10FSH 10-Inch Sliding Compound Miter Saw with Laser review, we checked out over 120 customer reviews. More than a few people called this the best miter saw that they have ever owned, and the average score these real life customers gave to this model was an impressive 4.4 out of 5 stars. To make precision, perfect cuts on even the toughest lumber and building materials, you just can’t miss with the Hitachi C10FSH 10-Inch Sliding Compound Miter Saw with Laser.
Related posts:
Related posts brought to you by Yet Another Related Posts Plugin.
There are no comments yet, add one below.